V3 3d printer Reviews and Best Deals

Don't miss out on the promotions for V3 3d printer, buy V3 3d printer directly online and enjoy big saving on your purchases.

Latest V3 3d printer
Youmile CNC Shield V3.0 Expansion Board + Arduino UNO R3 Board+DRV8255 Stepper Motor Driver with Heatsink CNC Shield V3 Engraving Machine 3D Printer for Arduino Kits With USB Cable
  • Latest CNC Shield Version 3. 0 for Arduino
  • Arduino UNO R3 Board, MCU: ATmega328, USB interface: ATmega16U2
  • PWM spindle and direction pins. 4-Axis support. Runs on 12-36v DC
  • 2 x end stops for each axis (6 in total)
  • 4PCs DRV8255 stepper motor driver with radiator
DISCOUNTLatest V3 3d printer
ICQUANZX V3 Engraver Shield 3D Printer CNC Expansion Card A4988 Driver Board
  • This expansion board as a driver expansion board, can be used for engraving machines, 3D printers.
  • It is a total of four slots, can drive four A4988 stepper motor.
  • Each road stepper motors only need two IO ports.
  • UNO module IO port correspondence introduction.
Latest V3 3d printer
BIQU DIRECT TFT35 E3 V3.0 Touch Screen Display RepRap Smart Controller Panel Compatible with SKR V1.3 SKR PRO Board for Ender 3/CR10 3D Printer
  • ARM Cortex-M3 series STM32F207VCT6 chip with 32-bit CPU 120MHz
  • This display board has higher compatibility. Users can select two work modes: UART serial port screen mode and 12864 screen mode
  • Reserve the extension port of filament breaking detection (FIL-DET)
  • Reserve the extension port of automatic shutdown after printing (PS-ON)
  • LCD12864 mode uses EXP1, EXP2 and EXP3. EXP1 and EXP2 are LCD screen ports of normal motherboard. EXP3 is the LCD interface used by E3 series motherboard (such as SKR MINI E3 V1.2, etc.)
Latest V3 3d printer
KeeYees Professional 3D Printer CNC Kit with Tutorial for Arduino, CNC Shield V3 w/Jumpers + 4Pcs RAMPS 1.4 Mechanical Switch Endstop & DRV8825 GRBL Stepper Motor Driver Heat Sink
  • 【CNC Expansion Board with Free 20pcs Jumpers】This is the latest version of the expansion board, which can be used for engraving machines and 3D printers. It can drive 4 A4988/DRV8825 stepper motors. The jumper caps are necessary for CNC setups. You do not need to purchase this part extra.
  • 【DRV8825 Stepper Motor Driver w/ Heat Sink】DRV8825 is upgrade of A4988! It is a must-have module for 3D printers, CNCs and engraving machines. The 4-layer PCB board has better heat dissipation performance. 
  • 【Mechanical Switch Endstop】It uses a 22AWG wire that can withstand a current of 2A and a voltage of 300V. Better quality than traditional copper wire. It can reach the insulation temperature of 80℃. It is not easy to break, and very convenient to plug and remove.
  • 【Reliable Technical Support】We have prepared detailed tutorial, please visit our website( www.keeyees.com ) to get relevant information or can contact us on Amazon, we will send PDF Document to you.
Latest V3 3d printer
BIGTREETECH TFT35 V3.0 Graphic Smart Display Controller Board for 3D Printer Ramps 1.4 RepRap 3D Printer Can Select Two Work Modes
  • 1.Upgrade the firmware by SD card. It is easy and convenient to operate.This display board has higher compatibility. Users can select two work modes,they are UART serial port screen mode and 12864 screen mode.
  • 2.Serial port screen mode supports two printing modes: SD card and U disk.
  • 3.Reserve WIFI port, and WIFI function is realized by external WIFI module;
  • 4.Reserve the extension port of filament breaking detection (FIL-DET);Reserve the extension port of automatic shutdown after printing (PS-ON);2 sets of UART serial port extension ports are reserved for DIY use.
  • 5.If there are any issue with the product, or if there are any problems in use, please contact the customer service team by message in time. We will try our best to assist you
Latest V3 3d printer
Kingprint TMC2208 V3.0 Stepper Damper with Heat Sink Driver, Replacement Damper for A4988 DRV8825 for 3D Printer (4 pieces) (TMC2208-V3.0-UART)
  • Advantages of UART mode
  • The motor current can be set arbitrarily via firmware;
  • The microsteps can be set arbitrarily via firmware (up to 256 actual microsteps).
  • The actual and interpolated microsteps can be combined to achieve maximum torque.
  • The firmware can dynamically switch the stepper motor between stealthChop2 and SpreadCycle mode via UART. If the engine is not moving, the engine standby power can be dynamically reduced (via the UART).
Latest V3 3d printer
BIQU DIRECT TFT35 V3.0 Touch Screen Display RepRap Smart Controller Panel Compatible with SKR V1.3 SKR PRO Board for 3D Printer Part
  • ARM Cortex-M3 Series STM32F207VCT6 Microprocessor with 32-bit CPU 120MHz
  • Update the firmware with the SD card. It is easy and convenient to use.
  • This scoreboard has greater compatibility. Users can choose two working modes, they are UART serial port display mode and 12864 display mode
  • Serial port display mode supports two print modes: SD card and U-disk
Latest V3 3d printer
AZDelivery CNC Shield V3 Development Board Bundle with Set of 4 A4988 Stepper Motor Drivers for 3D Printer and Arduino including eBook
  • AZ-Delivery CNC Shield V3 Development Board Bundle for 3D Printer and Arduino UNO R3 consists of CNC shield version 3.0 for Arduino and Set of 4 A4988 Stepper Motor Drivers.
  • AZ-Delivery CNC Shield V3 Development Board for A4988 Stepper Motor Driver for 3D Printer and Arduino UNO R3 has 4 Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13).
  • A4988 DMOS Stepper Motor Drivers are ideal for stepper motors with phase current of 2A (e.g., the NEMA17 motors for 3D printers).
  • Input voltage of the AZ-Delivery CNC Shield V3.0 is: 12 V - 36 V.
  • Of course, with the purchase from AZ-Delivery Vertriebs GmbH you will automatically receive an invoice including VAT by British standards, and the high AZ-Delivery quality and fast delivery directly from our UK warehouse including free eBook for your project .
Latest V3 3d printer
Comgrow BL Touch Auto-Leveling for Creality 3D Printer Ender 3 / Ender 3 Pro/Emder-5
  • BLTouch is an auto leveling sensor for 3D Printers that can precisely measure the tilt of Bed surface. It could work with any kinds of bed materials, such as glasses, woods, metals, and so on.
  • BLTouch is fulfilled with simple structure and high precision by using progressively designed solenoid and hall sensor. It aims for user convenience and enjoyable printing by adding many smart functions, such as self-test, alarm, alarm release & Touch Switch mode, Blue LED for servo signal indicating and Z-probe(Zmin) Testing.
  • Self-test : The push pin operate two times in a test when the power is on.
  • Alarm : The LED light blinks if a problem was found on a self-test or during operation.
  • Wiring defect indicator : Blue and Red LED for indicating wiring defects.

On this page you will find the list of the best V3 3d printer including the technical sheet, reviews issued by people who have already purchased the product, info on the updated price and active promotions and deals in the United Kingdom (UK).

V3 3d printer | Overview


DISCOUNTBest
ICQUANZX V3 Engraver Shield 3D Printer CNC Expansion Card A4988 Driver Board
  • This expansion board as a driver expansion board, can be used for engraving machines, 3D printers.
  • It is a total of four slots, can drive four A4988 stepper motor.
  • Each road stepper motors only need two IO ports.
  • UNO module IO port correspondence introduction.
Best
BIQU DIRECT SKR Mini E3 32Bit Control Board with TFT35 E3 V3.0 Touch Screen Display RepRap Smart Controller Panel Replacement Original Touch Screen for Ender 3 3D Printer
  • BIGTREE_TFT35_V3.0. ( version number).bin
    First copy the above firmware to SD root directory, and then insert the card into the SD card slot of the board. Next please re-power the board or press the reset key, and wait for about 10 seconds before the update is completed.
    3. For DIY board firmware, please refer to the file TFT35-E3 V3.0PIN.

    Something Important
    1. When using 12864 screen mode, connect the port EXP1 and EXP2 to the motherboard. There is no touch funct

  • Integrated with the TMC2209 UART mode, reserves the DIAG extended port, convenient users to replace endstop Functions
  • Support BigTREETECH TFT24/TFT35 Touch Screen and Ender 3D printer original LCD 12864 screen
  • LCD12864 mode uses EXP1, EXP2 and EXP3. EXP1 and EXP2 are LCD screen ports of normal motherboard. EXP3 is the LCD interface used by E3 series motherboard (such as SKR MINI E3 V1.2, SKR E3 DIP V1.1, etc.)
  • SKR MINI E3 with TFT35 E3 V3.0 can replace the original control board and touch screen to work perfectly on Ender 3 printer
Best
KeeYees Professional 3D Printer CNC Kit with Tutorial for Arduino, CNC Shield V3 w/Jumpers + 4Pcs RAMPS 1.4 Mechanical Switch Endstop & DRV8825 GRBL Stepper Motor Driver Heat Sink
  • 【CNC Expansion Board with Free 20pcs Jumpers】This is the latest version of the expansion board, which can be used for engraving machines and 3D printers. It can drive 4 A4988/DRV8825 stepper motors. The jumper caps are necessary for CNC setups. You do not need to purchase this part extra.
  • 【DRV8825 Stepper Motor Driver w/ Heat Sink】DRV8825 is upgrade of A4988! It is a must-have module for 3D printers, CNCs and engraving machines. The 4-layer PCB board has better heat dissipation performance. 
  • 【Mechanical Switch Endstop】It uses a 22AWG wire that can withstand a current of 2A and a voltage of 300V. Better quality than traditional copper wire. It can reach the insulation temperature of 80℃. It is not easy to break, and very convenient to plug and remove.
  • 【Reliable Technical Support】We have prepared detailed tutorial, please visit our website( www.keeyees.com ) to get relevant information or can contact us on Amazon, we will send PDF Document to you.
Best
BIGTREETECH TFT35 V3.0 Graphic Smart Display Controller Board for 3D Printer Ramps 1.4 RepRap 3D Printer Can Select Two Work Modes
  • 1.Upgrade the firmware by SD card. It is easy and convenient to operate.This display board has higher compatibility. Users can select two work modes,they are UART serial port screen mode and 12864 screen mode.
  • 2.Serial port screen mode supports two printing modes: SD card and U disk.
  • 3.Reserve WIFI port, and WIFI function is realized by external WIFI module;
  • 4.Reserve the extension port of filament breaking detection (FIL-DET);Reserve the extension port of automatic shutdown after printing (PS-ON);2 sets of UART serial port extension ports are reserved for DIY use.
  • 5.If there are any issue with the product, or if there are any problems in use, please contact the customer service team by message in time. We will try our best to assist you
Best
Youmile CNC Shield V3.0 Expansion Board + Arduino UNO R3 Board+DRV8255 Stepper Motor Driver with Heatsink CNC Shield V3 Engraving Machine 3D Printer for Arduino Kits With USB Cable
  • Latest CNC Shield Version 3. 0 for Arduino
  • Arduino UNO R3 Board, MCU: ATmega328, USB interface: ATmega16U2
  • PWM spindle and direction pins. 4-Axis support. Runs on 12-36v DC
  • 2 x end stops for each axis (6 in total)
  • 4PCs DRV8255 stepper motor driver with radiator

Finding the cheapest prices on products sold in the United Kingdom (UK) can be rather time consuming, so we've taken it upon ourselves to help find the best bargains on the hottest products.

We'll keep this list of deals updated regularly, so be sure to check in often and make sure to find the cheapest prices on a variety of product categories in the entire the United Kingdom (UK).

We have categorized the products in order to show the most popular and best sellers.

Best V3 3d printer

Here is the ranking of the best V3 3d printer, click to see reviews, details and active promotions:

Visit our section devoted to providing consumer opinions on V3 3d printer and read the reviews left by real customers, see the V3 3d printer ranking and find the store where to buy at the lowest price.

V3 3d printer New
SNOWINSPRING TMC2208 V3.0 Stepper Mute with Heat Sinks Driver Stepstick Mute Replacement A4988 Drv8825 for 3D Printer(Pack Of 4 PCS)
  • TMC2208 is a super mute two-phase stepper motor drive chip, continuous drive current 1.4A, current 2 A, voltage range 4.75v-36v,256 subdivision.
  • The flexible Microplyer interpolation unit can provide up to 256 subdivision, even in a system with limited pulse frequency, sine control can be perfectly realized.
  • With standard Step/dir interface, it is simple and convenient to use.
  • The high load driver does not lose its step, and the TMC2208 of the spreadcycle mode guarantees that the stepper motor will smooth over 0 o'clock without the dead-zone current.
  • STEALTHCHOP2 Ultra Mute technology can drive motor work in the case of extreme mute, can realize the control motor sound under 10dB decibels, the noise is much lower than the traditional current control mode.
V3 3d printer New
Milageto 3D Printer Kit RAMPS 1.4 Mega2560 A4988 2004LCD Controller Reprap
  • RAMPS interfaces an Mega with the powerful MEGA platform and has plenty room for expansion.
  • The RAMPS 1.4 board is designed to fit the entire electronics needed for a RepRap in one small package for low cost.
  • Additionally, a number of expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack
  • RAMPS 1.4
  • The modular design includes plug in stepper drivers and extruder control electronics on an MEGA for easy service, part replacement, upgrade-ability and expansion.
V3 3d printer New
Redrex Auto Leveling Sensor 3D Touch Probe V3.0 Upgrading Parts for ANET A8,CR10 Series,Ender 3 Series and Other DIY 3D Printers
  • Upgrading Bed Leveling kits:3D Touch is an auto leveling sensor for most open-source 3d printers.Such as ANET A8,CR10 and Ender 3 series,ANYCUBIC i3 Mega,Geeetech A10.
  • Smart and Precise Sentor:It could work with nearly any kind of bed materials,such as glasses,PCB,metals and so on.
  • Easy Installation:Like most other auto leveling sensors,this 3D Touch is easy to install on 3d printer,there are many STLs in thingiverse.com
  • Intelligence, self - check and alarm. Function of auto leveling is adopted to make it easier to use and to increase the success rate of shaping.
  • NOTE:Pulling/pushing hard on the push-pin can damage Touch sensorand make it less accurate.
V3 3d printer New
YO-TOKU TMC2130 V3.0 Stepper Motor StepStick Mute Silent Driver with Heatsink for 3D Printer Control Board 4 Packs(SPI) Motors
  • The chip is facing down,the pure gold process,and the heat dissipation function is strengthened.
  • Highlights:TMC2130 V3.0 is a new module that has been optimized .
  • Working Performance:The use of sequexternal sequencer can greatly reduce the working load of the chip,effectively avoiding the errors caused by the chip overload,the missing step and the trouble.
  • Compatible:MKS Gen V1.4/mks Gen L v1.0/ramps 1.6/SKR V1.3 and so on.
  • Note:This module is similar to TMC2100,which produces a lot of thermal energy at work.Therefore,in the use of the process,it is necessary to increase the radiator and cooling fan to cool,reduce the loss of the steps and operating deviations.
V3 3d printer New
Nologo YO-TOKU TFT35 V3.0 Graphic Smart Display Controller Board for 3D Printer Ramps 1.4 RepRap 3D Printer Can Select Two Work Modes Modules CE
  • 4.Reserve the extension port of filament breaking detection (FIL-DET);Reserve the extension port of automatic shutdown after printing (PS-ON);
  • 1.Upgrade the firmware by card. It is easy and convenient to operate.This display board has higher compatibility. Users can select two work modes,they are UART serial port screen mode and 12864 screen mode.
  • 3.Reserve WIFI port, and WIFI function is realized by external WIFI module;
  • 2.Serial port screen mode supports two printing modes: card and U disk.
  • 5.2 sets of UART serial port extension ports are reserved for DIY use.
V3 3d printer New
YO-TOKU 3D Printer Part Stepstick Mute TMC2130 V3.0 Stepper Motor Driver with Heat Sink for SKR V1.3 Ramps 1.6 1.5 MKS GEN L Control Board (Step/Dir) Motors
  • Passive Braking and freewheeling mode
  • cool Step current control for energy savings up to 75%
  • spread Cycle highly dynamic motor control chopper
  • for extremely quiet operation and smooth motion
  • Full & Diagnostics
V3 3d printer New
Naliovker 3D Printer CNC Controller Kit with for IDE GRBL CNC Board RAMPS 1.4 Mechanical Switch Endstop DRV8825 A4988 Stepper Motor Driver Nema 17 Stepper Motor
  • 2. R3 Board, MCU: ATmega328, USB interface: ATmega16U2 with 1.5m USB cable.
  • 4.Nema 17 Stepper Motor 59 Ncm (84 oz.in) 47mm Body 1.8 degree with mounting bracket kit.
  • 1.100% brand new
  • 3.DRV8825 Stepper Motor Driver with heat sink, upgraded from A4988, max.current: 2.5A, 32 subdivision: 1, 1/2, 1/4, 1/8, 1/16, 1/32.
  • 5.CH340G CNC Shield expansion board Version 3.0 for , and compatible for GRBL 0.9.
V3 3d printer New
B Blesiya AIO II V3.2 MCU 32 Bit Controller Board W / TMC2208 Step Driver Panel For CNC
  • 4 pieces of ST820 stepper drivers, 256 Microsteps.
  • CH340 for high USB serial connection and firmware upload.
  • STM32F103 MCU (Run Marlin 2.0).
  • Fully integrated all in one solution:
  • This is an All In One (So we call it AIO) solution with 32-bit MCU and 256-microsteps stepper motor drive for 3DP/CNC or similar machine.It has everything you need to assemble a 3DP, including a display and an SD card holder.
V3 3d printer New
BIQU DIRECT SKR Mini E3 V2.0 32-bit control board with TFT35 E3 V3.0 touchscreen display RepRap Smart Controller Panel replacement Original touchscreen for Ender 3 / Ender 3 Pro CR-10 3D printer
  • 32bit main frequency 72MHz ARM level Cortex-M3 series STM32F103RCT6 Microprocessor
  • 4 Layers PCB for better heat dissipation
  • Sensorless homing function by plugging in the jump cap
  • Supports BL touch, locked-rotation detection, power-off resume, shutdown after Finish Printing
  • Parallel type double Z axis interface

V3 3d printer | Reviews

On this page you can find a list of products with their reviews and opinions issued by customers who have already purchased V3 3d printer.

Learn directly from other people's shopping experience: they are useful to understand the quality of the product, if it really corresponds to what is going to be shipped, if there are production defects or if there is anything else that you should know.

Users who release reviews on V3 3d printer give useful information not only about the purchasing experience but also about the use in real life, it is thanks to these feedback that you can learn valuable information about the product.

The proposed list ranks products based on the votes received, positive opinions and relevance to the customer needs.

Redrex Auto Leveling Sensor 3D Touch Probe V3.0 Upgrading Parts for ANET A8,CR10 Series,Ender 3 Series and Other DIY 3D Printers
  • Upgrading Bed Leveling kits:3D Touch is an auto leveling sensor for most open-source 3d printers.Such as ANET A8,CR10 and Ender 3 series,ANYCUBIC i3 Mega,Geeetech A10.
  • Smart and Precise Sentor:It could work with nearly any kind of bed materials,such as glasses,PCB,metals and so on.
  • Easy Installation:Like most other auto leveling sensors,this 3D Touch is easy to install on 3d printer,there are many STLs in thingiverse.com
  • Intelligence, self - check and alarm. Function of auto leveling is adopted to make it easier to use and to increase the success rate of shaping.
  • NOTE:Pulling/pushing hard on the push-pin can damage Touch sensorand make it less accurate.
Nologo YO-TOKU TFT35 V3.0 Graphic Smart Display Controller Board for 3D Printer Ramps 1.4 RepRap 3D Printer Can Select Two Work Modes Modules CE
  • 4.Reserve the extension port of filament breaking detection (FIL-DET);Reserve the extension port of automatic shutdown after printing (PS-ON);
  • 1.Upgrade the firmware by card. It is easy and convenient to operate.This display board has higher compatibility. Users can select two work modes,they are UART serial port screen mode and 12864 screen mode.
  • 3.Reserve WIFI port, and WIFI function is realized by external WIFI module;
  • 2.Serial port screen mode supports two printing modes: card and U disk.
  • 5.2 sets of UART serial port extension ports are reserved for DIY use.
SNOWINSPRING TMC2208 V3.0 Stepper Mute with Heat Sinks Driver Stepstick Mute Replacement A4988 Drv8825 for 3D Printer(Pack Of 4 PCS)
  • TMC2208 is a super mute two-phase stepper motor drive chip, continuous drive current 1.4A, current 2 A, voltage range 4.75v-36v,256 subdivision.
  • The flexible Microplyer interpolation unit can provide up to 256 subdivision, even in a system with limited pulse frequency, sine control can be perfectly realized.
  • With standard Step/dir interface, it is simple and convenient to use.
  • The high load driver does not lose its step, and the TMC2208 of the spreadcycle mode guarantees that the stepper motor will smooth over 0 o'clock without the dead-zone current.
  • STEALTHCHOP2 Ultra Mute technology can drive motor work in the case of extreme mute, can realize the control motor sound under 10dB decibels, the noise is much lower than the traditional current control mode.
BIQU DIRECT SKR Mini E3 V2.0 32-bit control board with TFT35 E3 V3.0 touchscreen display RepRap Smart Controller Panel replacement Original touchscreen for Ender 3 / Ender 3 Pro CR-10 3D printer
  • 32bit main frequency 72MHz ARM level Cortex-M3 series STM32F103RCT6 Microprocessor
  • 4 Layers PCB for better heat dissipation
  • Sensorless homing function by plugging in the jump cap
  • Supports BL touch, locked-rotation detection, power-off resume, shutdown after Finish Printing
  • Parallel type double Z axis interface
B Blesiya AIO II V3.2 MCU 32 Bit Controller Board W / TMC2208 Step Driver Panel For CNC
  • 4 pieces of ST820 stepper drivers, 256 Microsteps.
  • CH340 for high USB serial connection and firmware upload.
  • STM32F103 MCU (Run Marlin 2.0).
  • Fully integrated all in one solution:
  • This is an All In One (So we call it AIO) solution with 32-bit MCU and 256-microsteps stepper motor drive for 3DP/CNC or similar machine.It has everything you need to assemble a 3DP, including a display and an SD card holder.

V3 3d printer | Pricing

The price list can be subject to price variations based on any discount of the day, to find the last price, simply click on the dedicated button “see Price”.

How can you get the best deal? Read and learn in order to select the most convenient offer.

Latest V3 3d printer
Youmile CNC Shield V3.0 Expansion Board + Arduino UNO R3 Board+DRV8255 Stepper Motor Driver with Heatsink CNC Shield V3 Engraving Machine 3D Printer for Arduino Kits With USB Cable
  • Latest CNC Shield Version 3. 0 for Arduino
  • Arduino UNO R3 Board, MCU: ATmega328, USB interface: ATmega16U2
  • PWM spindle and direction pins. 4-Axis support. Runs on 12-36v DC
  • 2 x end stops for each axis (6 in total)
  • 4PCs DRV8255 stepper motor driver with radiator
DISCOUNTLatest V3 3d printer
ICQUANZX V3 Engraver Shield 3D Printer CNC Expansion Card A4988 Driver Board
  • This expansion board as a driver expansion board, can be used for engraving machines, 3D printers.
  • It is a total of four slots, can drive four A4988 stepper motor.
  • Each road stepper motors only need two IO ports.
  • UNO module IO port correspondence introduction.
Latest V3 3d printer
BIQU DIRECT TFT35 E3 V3.0 Touch Screen Display RepRap Smart Controller Panel Compatible with SKR V1.3 SKR PRO Board for Ender 3/CR10 3D Printer
  • ARM Cortex-M3 series STM32F207VCT6 chip with 32-bit CPU 120MHz
  • This display board has higher compatibility. Users can select two work modes: UART serial port screen mode and 12864 screen mode
  • Reserve the extension port of filament breaking detection (FIL-DET)
  • Reserve the extension port of automatic shutdown after printing (PS-ON)
  • LCD12864 mode uses EXP1, EXP2 and EXP3. EXP1 and EXP2 are LCD screen ports of normal motherboard. EXP3 is the LCD interface used by E3 series motherboard (such as SKR MINI E3 V1.2, etc.)
Latest V3 3d printer
KeeYees Professional 3D Printer CNC Kit with Tutorial for Arduino, CNC Shield V3 w/Jumpers + 4Pcs RAMPS 1.4 Mechanical Switch Endstop & DRV8825 GRBL Stepper Motor Driver Heat Sink
  • 【CNC Expansion Board with Free 20pcs Jumpers】This is the latest version of the expansion board, which can be used for engraving machines and 3D printers. It can drive 4 A4988/DRV8825 stepper motors. The jumper caps are necessary for CNC setups. You do not need to purchase this part extra.
  • 【DRV8825 Stepper Motor Driver w/ Heat Sink】DRV8825 is upgrade of A4988! It is a must-have module for 3D printers, CNCs and engraving machines. The 4-layer PCB board has better heat dissipation performance. 
  • 【Mechanical Switch Endstop】It uses a 22AWG wire that can withstand a current of 2A and a voltage of 300V. Better quality than traditional copper wire. It can reach the insulation temperature of 80℃. It is not easy to break, and very convenient to plug and remove.
  • 【Reliable Technical Support】We have prepared detailed tutorial, please visit our website( www.keeyees.com ) to get relevant information or can contact us on Amazon, we will send PDF Document to you.
Latest V3 3d printer
BIGTREETECH TFT35 V3.0 Graphic Smart Display Controller Board for 3D Printer Ramps 1.4 RepRap 3D Printer Can Select Two Work Modes
  • 1.Upgrade the firmware by SD card. It is easy and convenient to operate.This display board has higher compatibility. Users can select two work modes,they are UART serial port screen mode and 12864 screen mode.
  • 2.Serial port screen mode supports two printing modes: SD card and U disk.
  • 3.Reserve WIFI port, and WIFI function is realized by external WIFI module;
  • 4.Reserve the extension port of filament breaking detection (FIL-DET);Reserve the extension port of automatic shutdown after printing (PS-ON);2 sets of UART serial port extension ports are reserved for DIY use.
  • 5.If there are any issue with the product, or if there are any problems in use, please contact the customer service team by message in time. We will try our best to assist you
Latest V3 3d printer
Kingprint TMC2208 V3.0 Stepper Damper with Heat Sink Driver, Replacement Damper for A4988 DRV8825 for 3D Printer (4 pieces) (TMC2208-V3.0-UART)
  • Advantages of UART mode
  • The motor current can be set arbitrarily via firmware;
  • The microsteps can be set arbitrarily via firmware (up to 256 actual microsteps).
  • The actual and interpolated microsteps can be combined to achieve maximum torque.
  • The firmware can dynamically switch the stepper motor between stealthChop2 and SpreadCycle mode via UART. If the engine is not moving, the engine standby power can be dynamically reduced (via the UART).
Latest V3 3d printer
BIQU DIRECT TFT35 V3.0 Touch Screen Display RepRap Smart Controller Panel Compatible with SKR V1.3 SKR PRO Board for 3D Printer Part
  • ARM Cortex-M3 Series STM32F207VCT6 Microprocessor with 32-bit CPU 120MHz
  • Update the firmware with the SD card. It is easy and convenient to use.
  • This scoreboard has greater compatibility. Users can choose two working modes, they are UART serial port display mode and 12864 display mode
  • Serial port display mode supports two print modes: SD card and U-disk
Latest V3 3d printer
AZDelivery CNC Shield V3 Development Board Bundle with Set of 4 A4988 Stepper Motor Drivers for 3D Printer and Arduino including eBook
  • AZ-Delivery CNC Shield V3 Development Board Bundle for 3D Printer and Arduino UNO R3 consists of CNC shield version 3.0 for Arduino and Set of 4 A4988 Stepper Motor Drivers.
  • AZ-Delivery CNC Shield V3 Development Board for A4988 Stepper Motor Driver for 3D Printer and Arduino UNO R3 has 4 Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13).
  • A4988 DMOS Stepper Motor Drivers are ideal for stepper motors with phase current of 2A (e.g., the NEMA17 motors for 3D printers).
  • Input voltage of the AZ-Delivery CNC Shield V3.0 is: 12 V - 36 V.
  • Of course, with the purchase from AZ-Delivery Vertriebs GmbH you will automatically receive an invoice including VAT by British standards, and the high AZ-Delivery quality and fast delivery directly from our UK warehouse including free eBook for your project .
Latest V3 3d printer
Comgrow BL Touch Auto-Leveling for Creality 3D Printer Ender 3 / Ender 3 Pro/Emder-5
  • BLTouch is an auto leveling sensor for 3D Printers that can precisely measure the tilt of Bed surface. It could work with any kinds of bed materials, such as glasses, woods, metals, and so on.
  • BLTouch is fulfilled with simple structure and high precision by using progressively designed solenoid and hall sensor. It aims for user convenience and enjoyable printing by adding many smart functions, such as self-test, alarm, alarm release & Touch Switch mode, Blue LED for servo signal indicating and Z-probe(Zmin) Testing.
  • Self-test : The push pin operate two times in a test when the power is on.
  • Alarm : The LED light blinks if a problem was found on a self-test or during operation.
  • Wiring defect indicator : Blue and Red LED for indicating wiring defects.

V3 3d printer | Promotions and Deals (UK)

During the year there are many promotions on products for sale online and V3 3d printer could be subject to big discounts.

Promotions can be seen in the product presentation box, if a promotion is active you will see a green box with "offer".

We recommend to always click on the "see" button so that you can directly check the presence of Flash Sale Offers in the product form (offers that last only a few hours).

V3 3d printer | Cost

Below we have selected a list of V3 3d printer which are among the cheapest on the market. Just scroll through the list to find V3 3d printer the cheapest products.

V3 3d printer | Catalog

The product V3 3d printer can be found in the dedicated catalog where the entire list of products on sale is presented.

V3 3d printer is included in the 2020 catalog presentation along with the family of products belonging to the Brand.

V3 3d printer New
SNOWINSPRING TMC2208 V3.0 Stepper Mute with Heat Sinks Driver Stepstick Mute Replacement A4988 Drv8825 for 3D Printer(Pack Of 4 PCS)
  • TMC2208 is a super mute two-phase stepper motor drive chip, continuous drive current 1.4A, current 2 A, voltage range 4.75v-36v,256 subdivision.
  • The flexible Microplyer interpolation unit can provide up to 256 subdivision, even in a system with limited pulse frequency, sine control can be perfectly realized.
  • With standard Step/dir interface, it is simple and convenient to use.
  • The high load driver does not lose its step, and the TMC2208 of the spreadcycle mode guarantees that the stepper motor will smooth over 0 o'clock without the dead-zone current.
  • STEALTHCHOP2 Ultra Mute technology can drive motor work in the case of extreme mute, can realize the control motor sound under 10dB decibels, the noise is much lower than the traditional current control mode.
V3 3d printer New
Milageto 3D Printer Kit RAMPS 1.4 Mega2560 A4988 2004LCD Controller Reprap
  • RAMPS interfaces an Mega with the powerful MEGA platform and has plenty room for expansion.
  • The RAMPS 1.4 board is designed to fit the entire electronics needed for a RepRap in one small package for low cost.
  • Additionally, a number of expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack
  • RAMPS 1.4
  • The modular design includes plug in stepper drivers and extruder control electronics on an MEGA for easy service, part replacement, upgrade-ability and expansion.
V3 3d printer New
Redrex Auto Leveling Sensor 3D Touch Probe V3.0 Upgrading Parts for ANET A8,CR10 Series,Ender 3 Series and Other DIY 3D Printers
  • Upgrading Bed Leveling kits:3D Touch is an auto leveling sensor for most open-source 3d printers.Such as ANET A8,CR10 and Ender 3 series,ANYCUBIC i3 Mega,Geeetech A10.
  • Smart and Precise Sentor:It could work with nearly any kind of bed materials,such as glasses,PCB,metals and so on.
  • Easy Installation:Like most other auto leveling sensors,this 3D Touch is easy to install on 3d printer,there are many STLs in thingiverse.com
  • Intelligence, self - check and alarm. Function of auto leveling is adopted to make it easier to use and to increase the success rate of shaping.
  • NOTE:Pulling/pushing hard on the push-pin can damage Touch sensorand make it less accurate.
V3 3d printer New
YO-TOKU TMC2130 V3.0 Stepper Motor StepStick Mute Silent Driver with Heatsink for 3D Printer Control Board 4 Packs(SPI) Motors
  • The chip is facing down,the pure gold process,and the heat dissipation function is strengthened.
  • Highlights:TMC2130 V3.0 is a new module that has been optimized .
  • Working Performance:The use of sequexternal sequencer can greatly reduce the working load of the chip,effectively avoiding the errors caused by the chip overload,the missing step and the trouble.
  • Compatible:MKS Gen V1.4/mks Gen L v1.0/ramps 1.6/SKR V1.3 and so on.
  • Note:This module is similar to TMC2100,which produces a lot of thermal energy at work.Therefore,in the use of the process,it is necessary to increase the radiator and cooling fan to cool,reduce the loss of the steps and operating deviations.
V3 3d printer New
Nologo YO-TOKU TFT35 V3.0 Graphic Smart Display Controller Board for 3D Printer Ramps 1.4 RepRap 3D Printer Can Select Two Work Modes Modules CE
  • 4.Reserve the extension port of filament breaking detection (FIL-DET);Reserve the extension port of automatic shutdown after printing (PS-ON);
  • 1.Upgrade the firmware by card. It is easy and convenient to operate.This display board has higher compatibility. Users can select two work modes,they are UART serial port screen mode and 12864 screen mode.
  • 3.Reserve WIFI port, and WIFI function is realized by external WIFI module;
  • 2.Serial port screen mode supports two printing modes: card and U disk.
  • 5.2 sets of UART serial port extension ports are reserved for DIY use.
V3 3d printer New
YO-TOKU 3D Printer Part Stepstick Mute TMC2130 V3.0 Stepper Motor Driver with Heat Sink for SKR V1.3 Ramps 1.6 1.5 MKS GEN L Control Board (Step/Dir) Motors
  • Passive Braking and freewheeling mode
  • cool Step current control for energy savings up to 75%
  • spread Cycle highly dynamic motor control chopper
  • for extremely quiet operation and smooth motion
  • Full & Diagnostics
V3 3d printer New
Naliovker 3D Printer CNC Controller Kit with for IDE GRBL CNC Board RAMPS 1.4 Mechanical Switch Endstop DRV8825 A4988 Stepper Motor Driver Nema 17 Stepper Motor
  • 2. R3 Board, MCU: ATmega328, USB interface: ATmega16U2 with 1.5m USB cable.
  • 4.Nema 17 Stepper Motor 59 Ncm (84 oz.in) 47mm Body 1.8 degree with mounting bracket kit.
  • 1.100% brand new
  • 3.DRV8825 Stepper Motor Driver with heat sink, upgraded from A4988, max.current: 2.5A, 32 subdivision: 1, 1/2, 1/4, 1/8, 1/16, 1/32.
  • 5.CH340G CNC Shield expansion board Version 3.0 for , and compatible for GRBL 0.9.
V3 3d printer New
B Blesiya AIO II V3.2 MCU 32 Bit Controller Board W / TMC2208 Step Driver Panel For CNC
  • 4 pieces of ST820 stepper drivers, 256 Microsteps.
  • CH340 for high USB serial connection and firmware upload.
  • STM32F103 MCU (Run Marlin 2.0).
  • Fully integrated all in one solution:
  • This is an All In One (So we call it AIO) solution with 32-bit MCU and 256-microsteps stepper motor drive for 3DP/CNC or similar machine.It has everything you need to assemble a 3DP, including a display and an SD card holder.
V3 3d printer New
BIQU DIRECT SKR Mini E3 V2.0 32-bit control board with TFT35 E3 V3.0 touchscreen display RepRap Smart Controller Panel replacement Original touchscreen for Ender 3 / Ender 3 Pro CR-10 3D printer
  • 32bit main frequency 72MHz ARM level Cortex-M3 series STM32F103RCT6 Microprocessor
  • 4 Layers PCB for better heat dissipation
  • Sensorless homing function by plugging in the jump cap
  • Supports BL touch, locked-rotation detection, power-off resume, shutdown after Finish Printing
  • Parallel type double Z axis interface

V3 3d printer | Where to buy?

If you are asking yourself where to buy V3 3d printer? Buy online or directly in a shop?

  1. Online The advantages of online stores are the immediate availability of V3 3d printer, you can receive the products directly at home by courier (sometimes even without shipping costs). Online you can also consult the technical sheets that show the details and read the opinions of the users who have tried it.
  2. Physical Store In a physical store instead you can try the product with your own hands, you can directly see V3 3d printer and how it works and therefore have a clear idea on the purchase you are going to make. In some cases you can receive information from the experts in the store and then evaluate further information and features. We can basically say that buy online means savings. Most of the time online shops sells at higher prices.

V3 3d printer may be available or on arrival, only in some cases it will no longer be available; it suffice to read the details of the product card to see if it will return for sale soon.

The advantage of Amazon is that of be able to count on Prime , the service that reduces costs making shipping free in many cases.

Ebay on the other hand can rely on the guarantee of those who choose paypal as a payment method and different ads from V3 3d printer used.

V3 3d printer | Discounts and Coupons in the United Kingdom (UK)

If you are already considering buying on Amazon, we advise you to take a look at the Amazon Discount Coupon page so you can get an additional price discount.

Redrex Auto Leveling Sensor 3D Touch Probe V3.0 Upgrading Parts for ANET A8,CR10 Series,Ender 3 Series and Other DIY 3D Printers
  • Upgrading Bed Leveling kits:3D Touch is an auto leveling sensor for most open-source 3d printers.Such as ANET A8,CR10 and Ender 3 series,ANYCUBIC i3 Mega,Geeetech A10.
  • Smart and Precise Sentor:It could work with nearly any kind of bed materials,such as glasses,PCB,metals and so on.
  • Easy Installation:Like most other auto leveling sensors,this 3D Touch is easy to install on 3d printer,there are many STLs in thingiverse.com
  • Intelligence, self - check and alarm. Function of auto leveling is adopted to make it easier to use and to increase the success rate of shaping.
  • NOTE:Pulling/pushing hard on the push-pin can damage Touch sensorand make it less accurate.
Nologo YO-TOKU TFT35 V3.0 Graphic Smart Display Controller Board for 3D Printer Ramps 1.4 RepRap 3D Printer Can Select Two Work Modes Modules CE
  • 4.Reserve the extension port of filament breaking detection (FIL-DET);Reserve the extension port of automatic shutdown after printing (PS-ON);
  • 1.Upgrade the firmware by card. It is easy and convenient to operate.This display board has higher compatibility. Users can select two work modes,they are UART serial port screen mode and 12864 screen mode.
  • 3.Reserve WIFI port, and WIFI function is realized by external WIFI module;
  • 2.Serial port screen mode supports two printing modes: card and U disk.
  • 5.2 sets of UART serial port extension ports are reserved for DIY use.
SNOWINSPRING TMC2208 V3.0 Stepper Mute with Heat Sinks Driver Stepstick Mute Replacement A4988 Drv8825 for 3D Printer(Pack Of 4 PCS)
  • TMC2208 is a super mute two-phase stepper motor drive chip, continuous drive current 1.4A, current 2 A, voltage range 4.75v-36v,256 subdivision.
  • The flexible Microplyer interpolation unit can provide up to 256 subdivision, even in a system with limited pulse frequency, sine control can be perfectly realized.
  • With standard Step/dir interface, it is simple and convenient to use.
  • The high load driver does not lose its step, and the TMC2208 of the spreadcycle mode guarantees that the stepper motor will smooth over 0 o'clock without the dead-zone current.
  • STEALTHCHOP2 Ultra Mute technology can drive motor work in the case of extreme mute, can realize the control motor sound under 10dB decibels, the noise is much lower than the traditional current control mode.
BIQU DIRECT SKR Mini E3 V2.0 32-bit control board with TFT35 E3 V3.0 touchscreen display RepRap Smart Controller Panel replacement Original touchscreen for Ender 3 / Ender 3 Pro CR-10 3D printer
  • 32bit main frequency 72MHz ARM level Cortex-M3 series STM32F103RCT6 Microprocessor
  • 4 Layers PCB for better heat dissipation
  • Sensorless homing function by plugging in the jump cap
  • Supports BL touch, locked-rotation detection, power-off resume, shutdown after Finish Printing
  • Parallel type double Z axis interface
B Blesiya AIO II V3.2 MCU 32 Bit Controller Board W / TMC2208 Step Driver Panel For CNC
  • 4 pieces of ST820 stepper drivers, 256 Microsteps.
  • CH340 for high USB serial connection and firmware upload.
  • STM32F103 MCU (Run Marlin 2.0).
  • Fully integrated all in one solution:
  • This is an All In One (So we call it AIO) solution with 32-bit MCU and 256-microsteps stepper motor drive for 3DP/CNC or similar machine.It has everything you need to assemble a 3DP, including a display and an SD card holder.

V3 3d printer | Similar Products

Depending on your needs and brand preferences, there are several interesting alternative products or similar products that can perform the same function within certain limits.

By reading the reviews and opinions of these products you can understand if they can actually be a choice to consider as an alternative to V3 3d printer.

Rating: 3.16 of 5 - 32 votes
1 Star2 Stars3 Stars4 Stars5 Stars (32 votes, average: 3.16 out of 5)
Loading...

Best Deals

Aldi 3d printer Reviews and Best Deals


3d printer dial indicator Reviews and Best Deals


Sls 3d printer for sale Reviews and Best Deals